Ulla300 -cable heating mat 

Factory-made and tested Ulla300-cable heating mats for preventing vehicle access ramps, entrances and pavements from freezing. Can be rapidly and easily laid in concrete, sand and asphalt. A ready-to-connect mat is easy to lay in place, the gaps always being correct. It can be shaped without cutting the installations strips. The output is 300 W/m². Nominal voltage 230 V. Standard width of mats are 0,95 m, and lenghts at 1-m intervals from 2 to 12 m. Cold ends MCMK 5 meter and length of mat + 5 m.

Plug’n Heat -heating cable 

A cable, fitted with a plug, for keeping piping, water meters and other frost-prone places ice-free. The heating cable is a self-regulating cable, making a thermostat unnecessary. It can also be installed inside drinking water pipes. Length of connection leads 2.5 m. Power rating 9 W/m. Voltage 230 V. IP 68.

Tash single-conductor heating cables 

The TASH single-conductor series resistant cables are designed for keeping outdoor areas, pipes and containers icefree. Outer sheath of HFFR material resistant to chemicals. Max loading 30 W/m (concrete), 25 W/m (sand), 20 W/m (pipe surface).Operating temperature under current 80 ºC, momentarily 160 ºC. Max voltage 500 V. Min. bending radius 5x outside diameter of cabel.

Optiheat 9 

For keeping drinking water pipes from freezing indoors and outdoors. Polyethylene sheath. Cable dimensions 5.9 x 7.9 mm. Min. bending radius 35 mm.

Optiheat 10 and 25 

For preventing water pipes and drainpipes from freezing. Optiheat 10 is intended for plastic piping, whereas Optiheat 25 is intended for metal piping. Polyolefin sheath. Cables have a bonded jacket to ensure watertightness and mechanical durability. Cable dimensions 11.5 x 5.5 mm. Min. bending radius 25 mm.

Optiheat 15/30 

For keeping rainwater drainage systems, roofs and stairways from freezing. Can also be used for underfloor heating of small areas. Outer sheath of polyolefin, which is extremely resistant to UV radiation. Cables have a bonded jacket to ensure watertightness and mechanical durability. Cable dimensions 10.5 x 6.0 mm. Min. bending radius 25 mm.

Tash accessories 

By using EFPLP4 connection kit a twin-conductor heating cable can be connected to a cold cable or another heating cable. The kit can also be used for connecting cold cables to both ends of a single conductor cable.

Optiheat accessories 

EFPLP1 jointing kit containing joint and shrink accessories for the watertight extension of a cable by means of a connector cable (MMJ or MMCK) and a termiantion accessory. EFPLP2 jointing kit for connecting a heating cable to a junction box or a termiantion accessory. The cable is laid from the point of installation to the box either as it is or in a protective tube. The kit includes a cable-shaped rubber seal. EFPLV1 pressure resistant lead-through for laying Optiheat 9 and Plug'n Heat cables inside a water pipe.

Heating cable attachment accessories 

LT20 heat resistant tape for attaching a heating cable for piping. ALU50 aluminium tape, which is attached to the surface of the pipe in the same direction as the cable. SV10 is used for improving heat exchange to the pipe surface or valve. XBC1230 fixing strip, to which the heating cable is attached to ensure the correct gaps. PPN6 plastic mounting strip for attachment of Tash heating cable and assurance of correct gaps. PPN8 plastic mounting cable fixing strip for 2-conductor Tash heating cable attachment and to ensure correct gap. VP300 cable strain reliever for use when laying a heating cable in a drainpipe.

Frost protection thermostats 

Fully automatic snow- and ice melting control unit. Heat- and humidity informations. LCD-display with continous information of temperature and humidity. Available versions in Finnish, Swedish, German, English, Czech and French. Diagnosis of faults and potential-free information in case of fault situation. Possibility of manual steering. DIN-rail mounting. 230 V.

ECO500 thermostat 

For frost protection control of pipes. Nominal voltage 230V. Nominal current 16 A res. Max load 3600 W. Adjustment range +2 - +35 ºC. Sensor 4 m, extendable up to 25 m with 2 x 1,5 mm². Sensor 47 kohm / 25 ºC. Box AP9. IP55. The sensor is installed to the top surface of the pipe when the cable is used inside the pipe. When using the cable outside the pipe, the sensor must be installed opposite of the heating cable, to the presumably coldest spot.